 |
Subscribe to RSS
SITE HELP?
973-625-9292
EMAIL
|
|
|
0C3865
COMPLETE PLANTS
COMPLETE BRASS STRIP MILL (10273)
Ref:
10273
MACHINE # 10273
MACHINERY INTERNATIONAL CORPORATION IS OFFERING FOR SALE ON AN EXCLUSIVE BASIS
A COMPLETE FACTORY FOR THE MELTING, CASTING, ROLLING AND SLITTING OF BRASS AND
PHOSPHOR BRONZE STRIP UP TO 530mm WIDE. THE FACTORY, WHICH IS LOCATED IN THE
U.S.A. AND WHICH WAS IN FULL OPERATION UNTIL AUGUST 2006, IS BEING OFFERED FOR
SALE EITHER AS A COMPLETE FACTORY OR AS INDIVIDUAL MACHINES.
THE AVERAGE PRODUCTION, DEPENDING UPON PRODUCT MIX, WAS 1.7 MILLION POUNDS
(770 METRIC TONS) PER MONTH UTILIZING 80 WORKERS AND RUNNING THREE SHIFTS IN
MELTING, CASTING AND ANNEALING AND TWO SHIFTS IN ROLLING, CLEANING, PICKLING
AND SLITTING. THE MACHINES INCLUDE:
TECHNICA GUSS SINGLE STRAND CASTING LINE (10261)
MANUFACTURER: TECHNICA GUSS GMBH (GERMANY)
TYPE: HORIZONTAL CONTINUOUS STRIP CASTING LINE
PREVIOUS USE: BRASS
TAKEN OUT OF SERVICE: 2006
No. OF STRANDS: ONE
STRIP WIDTH:
MINIMUM: 14.6" (370mm)
MAXIMUM: 21.5" (546mm)
CASTING SPEED: 6.5 IPM (165mm/MIN.)
STRIP THICKNESS:
MINIMUM: 0.500" (12.7mm)
MAXIMUM: 0.720" (18.2mm)
MELTING FURNACE:
MANUFACTURER: AJAX MAGNATHERMIC
TYPE: INDUCTION
QUANTITY: ONE
EQUIPPED WITH SHAKER TABLE
HOLDING FURNACE:
CROP SHEAR
WITHDRAWAL UNIT
UPCOILER
-MAX. COIL WEIGHT: 15,000 LBS. (6804 KG)
METATHERM TWIN STRAND CASTING LINE (10262)
MANUFACTURER: METATHERM GMBH (AUSTRIA)
TYPE: HORIZONTAL CONTINUOUS STRIP CASTING LINE
PREVIOUS USE: BRASS STRIP
TAKEN OUT OF SERVICE: 2006
STRIP THICKNESS:
MINIMUM: 0.500" (12.7mm)
MAXIMUM: 0.720" (18.2mm)
CASTING SPEED: 6.5 IPM (165mm/MIN.)
No. OF STRAND CAST: 1 OR 2
WIDTH OF STRANDS:
MINIMUM: 2 x 14.6" (370mm)
MAXIMUM: 2 x 20.75" (527mm)
MELTING FURNACES:
MANUFACTURER: AJAX MAGNATHERMIC
TYPE: 450 KW INDUCTION
EQUIPPED WITH:
SHAKER TABLE
HOLDING FURNACE
WITHDRAWAL UNIT
CROP SHEAR
DUAL UPCOILER
-MAX. COIL WEIGHT: 15,000 LBS. (6804 KG)
NEMATRON PLC CONTROLS
METATHERM SINGLE STRAND CASTER (10263)
MANUFACTURER: METATHERM GMBH (AUSTRIA)
TYPE: HORIZONTAL CONTINUOUS STRIP CASTING LINE
PREVIOUS USE: BRASS STRIP
TAKEN OUT OF SERVICE: 2006
STRIP THICKNESS:
MINIMUM: 0.500" (12.7mm)
MAXIMUM: 0.720" (18.2mm)
STRIP WIDTH: 20.75" (527mm)
CASTING SPEED: 6 IPM (152mm/MIN.)
No. OF STRAND CAST: 1
MELTING FURNACES:
MANUFACTURER: AJAX MAGNATHERMIC
TYPE: INDUCTION
QUANTITY: ONE
EQUIPPED WITH:
SHAKER TABLE
HOLDING FURNACE
WITHDRAWAL UNIT
CROP SHEAR
UPCOILER
-MAX. COIL WEIGHT: 15,000 LBS. (6804 KG)
22" (560mm) TORRINGTON TWO-SIDED MILLING LINE (10264) SOLD
6" x 18" x 24" GRISET 2-HI/4-HI ROLLING MILL (10235) SOLD
26" (660mm) 20-HI SENDZIMIR MILL, NEW 1999 (10265) SOLD
13" (330mm) WATERBURY FARREL ZR33-13 Z-MILL (10243)
MANUFACTURER: WATERBURY FARREL COMPANY
TYPE: SENDZIMIR 20-HI COLD ROLLING MILL
MODEL: ZR33-13
S/N: 248873
MAXIMUM STRIP WIDTH: 14.250" (360mm)
ROLLING SPEEDS: 350/500 FPM
MATERIAL THICKNESS RANGE: 0.090" (2.286mm) TO 0.003" (0.0762mm)
MAX. WINDING TENSION: 3960# TO 500 FPM
MAX. WINDING TENSION: 5000# TO 330 FPM
MIN. WINDING TENSION: 750#
LINE CONSISTS OF:
UNCOILER:
TYPE: EXPANDING MANDREL
MANDREL SIZE: 12"/16" (305mm/406mm) I.D. x 16" (406mm) WIDE
EQUIPPED WITH:
-SNUBBER TAIL HOLDDOWN
-COIL CAR
HYDRAULIC ENTRY PINCH ROLLS w/EDGE GUIDE
REVERSING WINDERS (2):
TYPE: SOLID BLOCK
BLOCK SIZE: 16" (406mm) DIA. x 16" (406mm) FACE
DRIVE MOTOR: 50 HP, 400/1600 RPM, 120 AMP, 240 V
GEAR REDUCER: HORSBURGH & SCOTT, GEAR RATIO 12.9 TO 1
MILL MAIN DRIVE: 125 HP, 850/1800 RPM, 240 V, 424 AMP,
120 FLD. VOLT, 11.4 FLD. AMP, SCHULZ DC DRIVE
GEAR REDUCER: PHILADELPHIA, GEAR RATIO 3.37 TO 1
REWINDER:
MANUFACTURER: WATERBURY FARREL CORP.
TYPE: EXPANDING MANDREL
TYPE EXPANSION: HYDRAULIC
MANDREL SIZE: 14"/16" (355mm/406mm) x 14" (355mm) FACE
EQUIPPED WITH: COIL CAR
26" (660mm) WESERO PICKLING & CLEANING LINE, NEW 1996 (10271)
MANUFACTURER: WESERO EQUIPMENT CO.
YEAR OF MANUFACTURE: 1998 (FOR MOST COMPONENTS)
STRIP WIDTH: 12" - 26" (305mm - 660mm) WIDE
STRIP THICKNESS (BRASS): .008" - .160" (0.2mm - 4mm)
LINE SPEED: 0 - 200 FPM (0 - 60m/MIN.)
COIL SIZE: 20" (508mm) I.D.
COIL WEIGHT: 17,600 LBS. (7,983 KG)
PAYOFF:
20" HYDRAULIC EXPANDING MANDREL
ABOVE THE FLOOR COIL CAR
PINCH ROLL
LEVELLER (5 ROLL)
STITCHER
WRINGER ROLLS BEFORE, BETWEEN, AND AFTER ALL WET OPERATIONS (8 SETS TOTAL)
BRUSH DEGREASER, TOP AND BOTTOM. COLD RINSE PICKLE - SULFURIC ACID SPRAY TANK
10 FT. LONG. STEAM HEATED. COLD RINSE BRUSH - WESERO 2 TOP, 2 BOTTOM, QUICK
CHANGE, GRINDING CAPABILITY (20 FPM)
HOT RINSE
HOT PASSIVATION RINSE
STRIP DRYER
INSPECTION TABLE
DRIVE ROLL
CROP SHEAR
DRIVE ROLL
WINDING REEL WITH EDGE CONTROL
20" HYDRAULIC EXPANDING MANDREL
ABOVE THE FLOOR COIL CAR
26" (660mm) x 4-1/2" (108mm) RUESCH SLITTING LINE (10272)
MANUFACTURER: RUESCH MACHINE CO. (U.S.A.)
SERIAL No.: N3011 6280
CAPACITY (BASED ON PRIOR USE):
LINE SPEED: 0 - 500 FPM (0 - 127m/MIN.)
THICKNESS RANGE (BRASS): 0.025" - 0.153" (0.6mm - 3.8mm)
MAXIMUM WIDTH OF STRIP: 25" (635mm)
MAXIMUM COIL O.D.: 60" (1525mm)
MAXIMUM COIL WEIGHT: 15,000 LBS. (6800 KG)
LINE CONSISTS OF:
ENTRY COIL CAR: 18" x 34" (457mm x 865mm)
BED SIZE:
BED LINING: NEOPRENE
RIDES ON RAILS TO PAY-OFF
PAYOFF:
MANUFACTURER: RUESCH
TYPE: EXPANDING MANDREL
TYPE OF EXPANSION: HYDRAULIC
I.D. EXPANSION RANGE: 16"/20" (406mm/508mm)
18"/22" (457mm/866mm) WITH EXTENDERS
SLIDING BASE
PAPER UNWINDER
HYDRAULIC SNUBBER HOLDDOWN ROLL
ENTRY FEED TABLE:
TYPE: NEOPRENE
SIZE: 20" (508mm) W. x 60" (1524mm) L.
SLITTER HEAD:
ARBOR DIAMETER: 4 1/8" (105mm)
ARBOR LENGTH: 30" (762mm)
DRIVEN ENTRY PINCH ROLLS: 5" (127mm) DIA. x 30" (762mm) W.
ENTRY SIDE GUIDES: MANUAL
EDGE GUIDE SYSTEM: NORTH AMERICAN MFG. CO.
DRIVE MOTOR: 1.5 HP, 1750 RPM, 180 VOLT
ELECTRICAL CONTROLS: SCR THYRISTOR BY W.E.R. INDUSTRIAL WITH
SAFTRONICS SOLID STATE D.C. DRIVE
KNIFE SIZE: 4 1/8" (108mm) I.D. x 8" (203mm) O.D.
SPACER SIZE: 4 1/8" (108mm) I.D. x 5 1/4" (133mm) O.D.
EXIT PINCH ROLLS: 4" (102mm) x 29 1/2" (750mm)
EXIT TABLE:
TYPE: NEOPRENE
SIZE: 29" (736mm) W. x 102" (2590mm) L.
SCRAP WINDERS:
QUANTITY: 2 (MOUNTED ON A COMMON DRIVE)
DRIVE MOTOR: 2 HP, 1725 RPM, 208/230 V, 3 PH, 60 HZ
RECOILER:
TYPE:EXPANDING MANDREL
TYPE EXPANSION: HYDRAULIC
MANDREL SIZES (TWO DRUM SIZES):
SMALLER SIZE - QTY. 1: 16"/16 1/2" (406mm/420mm) I.D.
x 40" (102mm) WIDE
LARGER SIZE - QTY. 2: 20"/20 1/2" (508mm/520mm) I.D.
x 40" (102mm) WIDE
DRIVE MOTOR: 50 HP, 500/2000 RPM, 500 ARM VOLTS,
88 FLD AMPS, INTO 2-SPEED GEARBOX
WITH DUAL RATIOS 8.39/16.78
EQUIPPED WITH HYDRAULIC COIL PUSH-OFF
SINGLE ARM TURNSTILE:
FOR REMOVAL OF COIL FROM RECOILER
HYDRAULIC PUSH-OFF
360 DEGREE SWING
RUESCH COIL CAR FOR COIL DISCHARGE
BELL ANNEALING FURNACE (10266)
MANUFACTURER: LEE WILSON FURNACE CO. (U.S.A.)
TYPE: BELL ANNEALING FURNACES
FOR BRASS STRIP COILS
TYPE OF ATMOSPHERE: NITROGEN
TYPE OF POWER: GAS-FIRED
NUMBER OF FURNACES: ONE
NUMBER OF BASES: THREE
COIL O.D.: 66" (1676mm) MAXIMUM
HEIGHT OF STACKED COILS: 42" (1066mm) MAXIMUM
BELL ANNEALING FURNACE (10267)
MANUFACTURER: LEE WILSON FURNACE CO. (U.S.A.)
TYPE: BELL ANNEALING FURNACES
FOR BRASS STRIP COILS
TYPE OF ATMOSPHERE: NITROGEN
TYPE OF POWER: GAS-FIRED
NUMBER OF FURNACES: TWO
NUMBER OF BASES: FOUR
COIL O.D.: 89" (2260mm) MAXIMUM
HEIGHT OF STACKED COILS: 66" (1676mm) MAXIMUM
BELL ANNEALING FURNACE (10268)
MANUFACTURER: RADCON FURNACE COMPANY
TYPE: ATMOSPHERE CONTROLLED BELL ANNEALING
PREVIOUS USE: BRASS STRIP (SUITABLE FOR OTHER ALLOYS)
CONSISTS OF:
TWO BASES
TWO INNER COVERS
ONE FURNACE
ONE COOLING BELL FOR ANNEALING COPPER BASED ALLOY STRIP
NEW IN 1993
PROCESS SPECIFICATIONS:
CHARGE SIZE: 65" DIA. x 113" HIGH
CHARGE WEIGHT: 60,000 LBS. (ASSUMES 4-HI STACKS)
ANNEALING TEMPERATURE: 800 DEG. C. MAXIMUM
ANNEALING ATMOSPHERE: NITROGEN OR HYDROGEN
100% HYDROGEN CAPABLE
BELL ANNEALING FURNACE (10269)
MANUFACTURER: RADCON FURNACE COMPANY
TYPE: ATMOSPHERE CONTROLLED BELL ANNEALING
PREVIOUS USE: BRASS STRIP (SUITABLE FOR OTHER ALLOYS)
CONSISTS OF:
FIVE BASES
FIVE INNER COVERS
THREE FURNACES
TWO COOLING BELLS FOR ANNEALING COPPER BASED ALLOY STRIP
NEW IN 1998
PROCESS SPECIFICATIONS:
CHARGE SIZE: 65" DIA. x 132" HIGH
CHARGE WEIGHT: 80,000 LBS. (ASSUMES 4-HI STACKS)
ANNEALING TEMPERATURE: 800 DEG. C. MAXIMUM
ANNEALING ATMOSPHERE: NITROGEN OR HYDROGEN
100% HYDROGEN CAPABLE
BELL ANNEALING FURNACE (10270)
MANUFACTURER: RADCON FURNACE COMPANY
TYPE: ATMOSPHERE CONTROLLED BELL ANNEALING
PREVIOUS USE: BRASS STRIP (SUITABLE FOR OTHER ALLOYS)
CONSISTS OF:
TWO BASES
TWO INNER COVERS
ONE FURNACE
ONE COOLING BELL FOR ANNEALING COPPER BASED ALLOY STRIP
NEW IN 2001
PROCESS SPECIFICATIONS:
CHARGE SIZE: 90" DIA. x 132" HIGH
CHARGE WEIGHT: 80,000 LBS. (ASSUMES 4-HI STACKS)
ANNEALING TEMPERATURE: 800 DEG. C. MAXIMUM
ANNEALING ATMOSPHERE: NITROGEN OR HYDROGEN
100% HYDROGEN CAPABLE
PLEASE CONTACT US FOR FURTHER INFORMATION, QUOTATIONS OR INSPECTION VISITS.
**PRICE QUOTED IS EX WORKS AS IS WHERE IS SUBJECT TO PRIOR SALE**
**ALL SPECIFICATIONS ARE SUBJECT TO VERIFICATION BY PURCHASER**
Machinery International Corp
20 Commerce Dr
North Branford CT 06471-1250
Tel:
203-484-0400
Fax:
203-484-4499
Email:
sales@machyintl.com
Web:
www.machyintl.com
|
|
| |
|
|
